ISO INTERNATIONAL STANDARD 10896-2 First edition 2016-02-15 Rough-terrain trucks Safety requirements and verification Part 2: Slewing trucks Chariots tout-terrain - Exigences de sécurité et vérifications - Partie 2: Chariots rotatifs Reference number IS0 10896-2:2016(E) ISO International Organization for Standardization =ZHEJIANG INST OF STANDARDIZATION C1 5956617 @IS02016 vided by IHS under I Not for Resale, 2016/4/26 02:21:47 itted without license from IHS IS0 10896-2:2016(E) COPYRIGHTPROTECTEDDOCUMENT IS02016,PublishedinSwitzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 . CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyright@iso.org www.iso.org Intenationaibr Prganization for Standardization icensee-ZHEJIANG INST OF STANDARDIZoISQ s.6 - All rights reserved etworking permitted without license from IHS IS0 10896-2:2016(E) Contents Page Foreword ..vi Introduction. ..vii 1 Scope. 2 Normative references 3 Terms and definitions 4 Requirements 4.1 General .8 4.1.1 Sharp edges and acute angles 4.1.2 Stored energy components. ..8 4.1.3 Boom extension and angle indicators 4.2 Starting/moving. .8 4.2.1 'Unauthorized starting. .8 4.2.2 Unintended movement. .9 4.2.3 Uncontrolled motion. ..9 4.2.4 Powered travel movement. 9 4.2.5 Non-activation of the parking brake .9 4.2.6 Inching pedal. .9 4.3 Brakes .9 4.3.1 General. 4.3.2 Failure of energy supply .9 4.4 Electrical and electronic systems 10 4.4.1 General. .10 4.4.2 Degree of protection. .10 4.4.3 Electrical connections .10 4.4.4 Over-current protective devices. .10 4.4.5 Batteries .10 4.4.6 Battery disconnection .10 4.5 Controls. ..11 4.5.1 General .11 4.5.2 Differential locking. .11 4.5.3 Steering controls. .12 4.5.4 Load-handling controls .13 4.5.5 Multi-function controls ..13 4.5.6 Stabilizing device control ..13 4.5.7 Sway/levelling control .14 4.5.8 Axle oscillation locking .14 4.5.9 Auxiliary hydraulic control .14 4.6 Power systems and accessories. .14 4.6.1 Exhaust systems. ..14 4.6.2 Cooling systems ..14 4.6.3 Tanks and pressure vessels .14 4.7 Stabilizing devices. .15 4.8 Design requirements for maintenance purposes. ..15 4.8.1 General .15 4.8.2 Tiltable cab support device .16 4.9 Systems for lifting, tilting and reaching .16 4.9.1 Chains and wire ropes. .16 4.9.2 Hydraulic system. ..17 4.9.3 Maximum load-lowering speed ..17 4.9.4 Limitation of stroke. ..17 4.9.5 Fork arms, attachments, and quick couplers ..18 4.9.6 Slewing brake ..18 4.10 Normal operating position ..18 iii nsee=ZHEJIANG INST OF STANDARDIZATION C1 5956617 ted without license from IHS Not for Resale, 2016/4/26 02:21:47