ISO INTERNATIONAL STANDARD 17599 First edition 2015-01-15 Technical product documentation (TPD) General requirements of digital mock-up for mechanical products Documentation technique de produits (TPD) Exigences genérales de Digital mock-up pour les produits mécaniques Reference number IS0 17599:2015(E) ISO International Organization for Standardization @ IS0 2015 Institute of Sta andardization5956617 vided by IHS under I ted without license from IHS IS0 17599:2015(E) COPYRIGHTPROTECTEDDOCUMENT @ IS0 2015 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. ISO copyrightoffice Case postale 56:CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax +4122 749 09 47 E-mail copyright@iso.org Web www.iso.org Published in Switzerland Prganizationfor Standardization I by IHS unde Not for Resale, 2015/3/11 01:37:4 etworking permitted without license from IHS IS0 17599:2015(E) Contents Page Foreword ..V 1 Scope .1 2 Normative references 3 Terms and definitions 4 Abbreviations. 5 Classification of digital mock-up .3 5.1 Development stage .3 5.2 Purposes.. .3 5.3 Dataformat .3 6 Composition of digital mock-up ..4 6.1 Geometric information. 6.2 Constraint information .4 6.3 Engineering attributes .4 Requirements of a digital mock-up model ..4 7.1 General principles 4 7.2 Relationship between all kinds of digital mock-up ..4 7.3 Requirements of complete digital mock-up. .5 7.4 Requirements of sub-system digital mock-up ..5 7.5 Requirements of scheme digital mock-up. .5 7.6 Requirements of detailed digital mock-up .5 7.7 Requirements of manufacturing digital mock-up .6 7.8 Requirements of geometry digital mock-up .6 7.9 Requirements of function digital mock-up. 7.10 Requirements of performance digital mock-up .6 7.11 Requirements of special-purpose digital mock-up .1 7.12 Requirements of retrofit digital mock-up 8 Requirements of DMU building. .7 8.1 General requirements .7 8.1.1 General principles. .7 8.1.2 Fundamental requirements .7 8.1.3 Identification of parts or components .8 8.1.4 Definition and use of coordinate system. 8 8.1.5 Colouring and texture rendering requirements ..8 8.1.6 Model state. .8 8.2 Detailed requirements of model building. 8.2.1 Modelling of parts. .8 8.2.2 Assembly modelling. 8.2.3 Simulation modelling. .12 9 Simplification and lightweight models of digital mock-up ..13 9.1 Application ..13 9.2 General requirements ..13 10 Requirements of management. .13 10.1 General requirements .13 10.2 Management of the whole DMU life cycle ..14 10.2.1 General principles.. ..14 10.2.2 Management of design stage... ..14 10.2.3 Management of manufacture stage. .15 10.2.4 Management of marketing and aftermarket stages .15 10.3 Requirements of data management. .15 10.4 Configuration management. ..16 ntemaonalganizatin5All rights reserved iii ee=Zhejang Insttute of Standardization 5956617 Provided by IHS under license with ISO vithoutlicense from IHS Not for Resale, 2015/3/11 01:37:41