ISO INTERNATIONAL STANDARD 10904 First edition 2011-08-01 Fibre-cement corrugated sheets and fittings for roofing and cladding Plaques ondulees en fibrociment et leurs accessoires pour couvertures et revetements Reference number ISO 10904:2011(E) @ ISO 2011 IHSunder ted without license from IHS Not for Resale ISO 10904:2011(E) COPYRIGHTPROTECTEDDOCUMENT @ISO2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either isO at the address below or Iso's member body in the country of the requester. ISO copyright office Case postale 56 : CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISO 2011 - All rights reserved itted without license from IHS Not for Resale ISO 10904:2011(E) Contents Page Foreword Introductior 1 Scope 2 Normative references 3 Terms and definitions 4 Symbols, abbreviations and units. 5 Product requirements. 5.1 General. 5.2 Categorization and classification. 5.3 Dimensions and tolerances on nominal dimensions .8 5.4 Physicalrequirementsandcharacteristics. 5.5 Requirements concerning fire behavior.. 5.6 Productperformance.... 5.7 Requirements concerning impact resistance. 12 6 Evaluation of conformity 12 6.1 General 12 6.2 Typetesting 12 6.3 Quality control (QC) system 13 6.4 Inspectionofaconsignmentoffinishedproducts .15 7 Test requirements, 15 7.1 General 15 7.2 Dimensional and geometrical tests 15 7.3 Physical performance tests. 16 8 Marking. Annex A (normative) Consignment and inspection sampling ... 22 Annex B (normative) Dimensional and geometrical testing procedures. Annex C (normative) Test method to determine the breaking load and the bending modulus of sheets..... 31 Annex D (normative) Test method to determine the bending moment of a sheet. 35 Annex E (normative) Statistical method for determining the corresponding wet values or revised dry specifications for the breaking load and/or bending moment when carrying out the dry method of test or when testing prior to coating for quality control purposes... 37 Annex F (normative) Test method to determine the apparent density 40 Annex G (normative) Test method to determine the water permeability of a sheet ..42 Annex H (normative) Test method to determine the freeze-thaw performance of sheets and fittings...... Annex I (normative) Test method to determine the heat-rain performance of sheets. Annex J (normative) Test method to determine the warm water performance of long and short sheets ....... .49 Annex K (normative) Test method to determine the soak-dry performance of long and short sheets .... .51 Bibliography 53 ili from IHS Not for Resale

.pdf文档 ISO 10904 2011 Fibre-cement corrugated sheets and fittings for roofing and cladding

文档预览
中文文档 60 页 50 下载 1000 浏览 0 评论 309 收藏 3.0分
温馨提示:本文档共60页,可预览 3 页,如浏览全部内容或当前文档出现乱码,可开通会员下载原始文档
ISO 10904 2011 Fibre-cement corrugated sheets and fittings for roofing and cladding 第 1 页 ISO 10904 2011 Fibre-cement corrugated sheets and fittings for roofing and cladding 第 2 页 ISO 10904 2011 Fibre-cement corrugated sheets and fittings for roofing and cladding 第 3 页
下载文档到电脑,方便使用
本文档由 人生无常 于 2024-08-31 09:30:49上传分享
站内资源均来自网友分享或网络收集整理,若无意中侵犯到您的权利,敬请联系我们微信(点击查看客服),我们将及时删除相关资源。